New drill results include: B5MB4D059 - 10.19 metres @ 6.69% Cu,
0.48 g/t Au, 3.2% Zn & 20 g/t Ag from 33.5 metres in supergene
massive sulphides B5MB4D066 - 4.90 metres @ 15.94% Cu, 1.27 g/t Au
& 49.4 g/t Ag from 19.3 metres. B5MB4D074 - 35.09 metres @
4.82% Cu, 0.38 g/t Au, 0.85% Zn & 17.7 g/t Ag from 70.35 metres
down hole in a primary massive sulphide intersection TORONTO, Nov.
14, 2011 /CNW/ - Gentor Resources, Inc. ("Gentor" or the "Company")
& (OTCQB: GNTO) and their Omani partner Al Fairuz Mining
Company LLC are pleased to announce continued excellent results
from on-going evaluation drilling of their Oman Block 5, Mahab 4
Cyprus-type copper discovery. Further diamond drilling has
confirmed continuity of strong Massive Sulphide grades over 300
metres of strike, including high-grade supergene zones below gossan
exposures at the southern end of the deposit. These continued
impressive results from infill and extensional resource drilling by
two diamond rigs at Mahab 4 are expected to allow the calculation
of a maiden resource estimate on this high grade deposit by early
2012. By the end of October 2011, Gentor had completed 43
drillholes totalling 5,075.4 metres at Mahab 4. A recent
Laser scan DTM survey has provided accurate topographic and drill
hole collar information (see Table 2 below). Assay results received
from twelve new drill holes up to B5MB4D074 are summarised in Table
1 below and the drillhole intersections shown in the prospect
geology plan (see Figure 1 via the link below to Gentor's website).
An additional nine successful holes have been completed whose assay
results are awaited, and at least six more holes are planned to
complete definition of the main ore deposit shape on 50 metre
sections down to a nominal 150 metres depth below surface. Gentor
has initiated preliminary metallurgical test work on ten
representative samples of Massive Sulphide and Stringer Zone
samples from Mahab 4 at Wardell Armstrong's UK laboratory. Gentor
plans to restart drill evaluation of the Maqail South discovery in
December 2011 following completion of this phase of the Mahab 4
drill programme. Regional exploration continues across Blocks
5 & 6 in Oman with a reverse circulation drilling program of
some 3,000 metres planned for November/December 2011. Locality
plans of the Oman concessions, the key prospect areas and reported
drill holes on sections are found accompanying this press release
on the Company's web site:
http://www.gentorresources.com/s/NewsReleases.asp?ReportID=490430
Gentor's President & CEO Dr. Peter Ruxton commented:
"Understanding the geological model and structural controls has
allowed Gentor to efficiently target the high-grade massive
sulphide shoots at Mahab 4 and has outlined this deposit for
planned early resource definition and metallurgical testing. The
shallow depth of the Mahab 4 mineralisation suggests future
potential for a near-surface, high grade, open pittable ore body."
Results from the main massive sulphide intercepts include: --
GRB5D047 intersecting 24.4 metres of primary MS /SMS grading 4.68%
Cu, 0.21 g/t Au, 1.68% Zn and 13.8 g/t Ag from 96.6 metres, --
B5MB4D059 intersecting 10.19 metres of supergene MS grading 6.69%
Cu, 0.48 g/t Au, 3.2% Zn and 20 g/t Ag from 33.5 metres, --
B5MB4D064 intersecting 39.5 metres of gossan/MS/SMS grading 4.81%
Cu, 0.25 g/t Au, 0.38% Zn and 16.7 g/t Ag from 13.5 metres down
hole, including 16.85 metres grading 8.4% Cu, 0.25 g/t Au, 0.52% Zn
and 15.3 g/t Ag from 20.15 metres depth. -- B5MB4D066 intersecting
22.7 metres of gossan/MS/SMS grading 3.76% Cu, 0.54 g/t Au, 0.09%
Zn and 15.4 g/t Ag from 1.5 metres depth including 4.9 metres
grading 15.94% Cu, 1.27 g/t Au, 0.11% Zn and 49.4 g/t Ag from 19.3
metres down hole. -- B5MB4D074 intersecting 35.09 metres of primary
MS grading 4.82% Cu, 0.38 g/t Au, 0.85% Zn and 17.7 g/t Ag from
70.35 metres down hole. TABLE 1. Summary of Significant
Intersections at Mahab 4 from June - Oct. 2011.
__________________________________________________________________________________________
| Hole # | From | To | Intercept | Copper | Gold| Silver | Zinc |
Mineralisation |
|__________|________|________|___________|________|_____|________|________|________________|
|Mahab 4 | m | m | m | % | g/t | g/t | % | |
|__________|________|________|___________|________|_____|________|________|________________|
|GRB5D042 | 108.20 | 111.00 | 2.80 | 5.03 |0.17 | 17.7 | 1.29 | MS
|
|__________|________|________|___________|________|_____|________|________|________________|
| and| 119.70 | 129.90 | 10.20 | 5.25 |0.30 | 13.8 | 1.02 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
|GRB5D047 | 96.60 | 121.00 | 24.40 | 4.68 |0.21 | 13.8 | 1.68 |
MS/SMS |
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 98.75 | 116.39 | 17.64 | 6.14 |0.26 | 18.6 | 2.24 | MS/SMS
|
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 103.00 | 112.00 | 9.00 | 7.22 |0.25 | 15.8 | 1.93 | MS/SMS
|
|__________|________|________|___________|________|_____|________|________|________________|
|GRB5D048 | 57.20 | 65.00 | 7.80 | 1.24 |0.08 | 2.1 | 0.18 | QVS |
|__________|________|________|___________|________|_____|________|________|________________|
| and| 93.00 | 103.00 | 10.00 | 1.54 |0.07 | 1.4 | 0.18 | QVS |
|__________|________|________|___________|________|_____|________|________|________________|
| and| 113.89 | 129.00 | 15.11 | 0.49 |0.02 | 1.1 | 0.04 | QVS |
|__________|________|________|___________|________|_____|________|________|________________|
|GRB5D052 | 90.54 | 106.89 | 16.35 | 0.72 |0.05 | 1.4 | 0.13 | QVS
|
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 90.54 | 93.88 | 3.34 | 1.18 |0.04 | 1.3 | 0.07 | QVS |
|__________|________|________|___________|________|_____|________|________|________________|
| and incl:| 102.00 | 109.00 | 7.00 | 0.73 |0.06 | 2.2 | 0.21 | QVS
|
|__________|________|________|___________|________|_____|________|________|________________|
|GRB5D054 | 62.40 | 73.00 | 10.60 | 0.43 |0.03 | 0.5 | 0.04 |
QVS/SMS |
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 67.89 | 73.00 | 5.11 | 0.72 |0.04 | 0.8 | 0.05 | QVS/SMS |
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D057 | 104.15 | 107.00 | 2.85 | 0.44 |0.04 | 5.4 | 0.14 | QVS
|
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D059 | 33.50 | 43.69 | 10.19 | 6.69 |0.48 | 20.0 | 3.20 | MS
|
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D064 | 13.50 | 53.00 | 39.50 | 4.81 |0.25 | 16.7 | 0.38 |
GOS/MS/SMS |
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 20.15 | 37.00 | 16.85 | 8.40 |0.25 | 15.3 | 0.52 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D066 | 1.50 | 24.20 | 22.70 | 3.76 |0.54 | 15.4 | 0.09 |
GOS/MS |
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 19.30 | 24.20 | 4.90 | 15.94 |1.27 | 49.4 | 0.11 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D067 | 32.95 | 41.00 | 8.05 | 3.18 |0.53 | 24.0 | 0.39 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 33.90 | 38.70 | 4.80 | 4.59 |0.81 | 36.3 | 0.31 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
|B5MB4D074 | 70.35 | 105.44 | 35.09 | 4.82 |0.38 | 17.7 | 0.85 | MS
|
|__________|________|________|___________|________|_____|________|________|________________|
| incl:| 72.84 | 95.41 | 22.57 | 6.14 |0.38 | 20.9 | 1.08 | MS |
|__________|________|________|___________|________|_____|________|________|________________|
| and incl:| 99.25 | 105.44 | 6.19 | 4.01 |0.72 | 21.6 | 0.67 | MS
|
|__________|________|________|___________|________|_____|________|________|________________|
(Codes: MS = Massive Sulphide, SMS = Semi-Massive Sulphide, QVS =
Quartz Vein Stringer, GOS = Gossan) TABLE 2. Core holes completed
at Mahab 4 (June to Oct. 2011)
__________________________________________________________________
|Hole No | Section | Easting | Northing | Dip | Azi | Length | | |
| | | | | (m) |
|__________|_________|_________|__________|_______|_______|________|
|GRB5D048 | 0 | 468775 | 2656105 | 60 | 255 | 135.15 |
|__________|_________|_________|__________|_______|_______|________|
|GRB5D050 | 0 | 468808 | 2656115 | 60 | 255 | 145.85 |
|__________|_________|_________|__________|_______|_______|________|
|GRB5D052 | 0 | 468677 | 2656063 | 50 | 060 | 117.40 |
|__________|_________|_________|__________|_______|_______|________|
|GRB5D054 | 1S | 468714 | 2656035 | 50 | 075 | 84.05 |
|__________|_________|_________|__________|_______|_______|________|
|GRB5D055 | 2S | 468734 | 2655999 | 50 | 075 | 96.00 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D057 | 1S | 468674 | 2656025 | 50 | 075 | 115.50 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D059 | 1S | 468741 | 2656040 | 49 | 065 | 55.10 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D061 | 2S | 468754 | 2656009 | 50 | 075 | 49.30 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D063 | 1S | 468795 | 2656058 | 90 | 0 | 46.50 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D064 | 1 | 468760 | 2656139 | 60 | 255 | 77.00 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D066 | 0 | 468767 | 2656104 | 60 | 255 | 64.85 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D067 | 0 | 468780 | 2656104 | 45 | 252 | 85.50 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D069 | 1.5S | 468748 | 2656024 | 50 | 075 | 52.50 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D070 | 1S | 468771 | 2656049 | 75 | 255 | 85.30 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D071 | 4.5 | 468762 | 2656316 | 60 | 255 | 141.50 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D072 | 1 | 468656 | 2656103 | 50 | 072 | 132.45 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D074 | 4.5 | 468761 | 2656314 | 60 | 277 | 126.00 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D075 | 2 | 468708 | 2656181 | 75 | 075 | 55.10 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D077 | 5.5 | 468758 | 2656362 | 60 | 255 | 79.30 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D079 | 2 | 468678 | 2656168 | 64 | 075 | 130.35 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D080 | 6 | 468752 | 2656387 | 60 | 255 | 154.60 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D082 | 3 | 468701 | 2656218 | 72 | 075 | 123.70 |
|__________|_________|_________|__________|_______|_______|________|
|B5MB4D083 | 3.5 | 468763 | 2656265 | 60 | 255 | 105.20 |
|__________|_________|_________|__________|_______|_______|________|
DRILL RESULTS The northern end of the deposit is discussed first on
a sectional basis followed by the southern end and central
sectional drill results (refer to Figures 1 to 6 via the above link
to Gentor's website for interpretative details). Section 4
--GRB5D042 and GRB5D047 tested the lateral extent of the GRB5D035
major intersection shown in Figure 3 and previously reported in
July 2011. GRB5D042 a scissor hole from the west intersected the
Main Fault then 2.80 metres of MS grading 5.03% Cu, 0.17 g/t Au,
1.29% Zn and 17.7 g/t Ag from 108.20 metres and 10.20 metres of MS
grading 5.25% Cu, 0.30 g/t Au, 1.02% Zn and 13.8 g/t Ag from 119.70
metres. These zones define a narrow width to the MS at this level.
GRB5D047 intersected 24.40 metres of MS/SMS grading 4.68% Cu, 0.21
g/t Au, 1.68% Zn and 13.8 g/t Ag from 96.60 metres and includes
9.00 metres grading 7.22% Cu, 0.25 g/t Au, 1.93% Zn and 15.8 g/t Ag
from 103.00 metres. This confirms the high grade zone in GRB5D035
extends at depth down dip to the east but it is cut off by an
eastern fault (see Figure 3). Section 4.5 -- B5MB4D071 and
B5MB4D074 effectively extended the strike extent of the MS north
into Section 5 where GRB5D041 and GRB5D045 had previously failed to
intersect the deposit. B5MB4D071 drilled parallel and 25 metres
north of GRB5D035 provided an excellent result of a similar very
strongly mineralised zone of MS, SMS and QVS from 63-128 metres
including 45 metres of chalcopyrite-rich MS down to 108 metres for
which final assays are not yet available. This encouraging result
showed the deposit remained open to the north - so a second drill
hole GRB5D074 from the same site was angled towards Section 5.
B5MB4D074 also provided a strong primary massive sulphide
intersection of 35.09 metres grading 4.82% Cu, 0.38 g/t Au, 0.85%
Zn and 17.7/t Ag from 70.35 metres down hole ended at 105.44 metres
with a sharp conformable transition to strongly altered footwall
V1-1 lavas. The latter part of this intersection lies beneath the
barren intersection in GRB5D041 on Section 5 and shows the deposit
is open at depth. Sections 5.5 and 6-- B5MB4D077 and B5MB4D080
further tested the northern strike extension of the deposit.
B5MB4D077 collared 50 metres north of B5MB4D074 on Section 5.5
intersected 30cm of pyritic MS from 70.4 metres below a thin
magnetite rich umber and then sedimentary breccias above V1-1
footwall lavas. This result suggests a distal exhalative
position and indicates the deposit has thinned rapidly to the north
from B5MB4D074, or there may be some cross structural control at
the northern end of the deposit. B5MB4D080 was collared 25 metres
north of D077 on Section 6 looking for any northern extension, but
failed to intersect a mineralised seafloor position with only thin
umbers between 85.80 metres and 90.10 metres and jasper clasts at
103 metres. This hole implies the deposit may have terminated just
north of the D077 position. Section 2S and 1.5S -- B5MB4D055,
B5MB4D061 and B5MB4D069 tested the southern strike extensions of
the deposit located on Section 1 in the southern wadi. All of these
holes failed to intersect the Main Fault or the mineralised package
containing the Mahab 4 deposit, therefore it is concluded that an
east-east cross fault parallel to the sections as shown in Figure 2
has cut off the deposit and may have displaced it at depth to the
east. Section 1S - BGRB5D054, B5MB4D057, B5MB4D059, B5MB4D063 and
B5MB4D070 defined the southern strike extent of the deposit in the
southern wadi (see Figure 6). Initial drillholes B5MB4D054 and
B5MB4D057 testing the QVS part of the system intersected moderate
to low grade copper including 10.6 metres of QVS/SMS grading 0.43%
Cu, 0.03 g/t Au from 60.4 metres in B5MB4D054 and 2.85 metres at
0.44% Cu, 0.04 g/t Au from 104.15 metres in B5MB4D057 that is
interpreted be close to the bottom of the deposit. However,
overlying this weak mineralisation, drillhole B5MB4D059 intersected
10.19 metres of supergene MS grading 6.69% Cu, 0.48 g/t Au, 3.2% Zn
and 20 g/t Ag from 33.5 metres adjacent to the Main Fault zone and
ending at an eastern fault (see Figure 4). This high-grade
intersection represented a break through in the evaluation of the
southern end of the deposit, because it showed that good MS can be
found at shallow depth beneath mapped gossan and above weak QVS
stringer mineralisation at depth. B5MB4D063 designed to test any
eastern down-dip/stratigraphic extension of the B5MB4D059 MS failed
to intersect sulphide mineralisation at depth in footwall V1-1
lavas, but did hit shallow oxidised copper from 13-16 metres in
basalt indicating leakage from subsurface gossan exposure upstream.
B5MB4D070 was designed to provide a full intersection of the
oxide-supergene MS-primary MS-QVS transitions on Section 1S
primarily for metallurgical purposes. It achieved an excellent
result with mineralisation virtually from the surface including 6.5
metres of ferruginous gossan below wadi gravel from 7 metres depth,
a 6 metre thick zone of chalcocite supergene enriched MS from 12.45
metres above a primary MS zone to 36.1 metres. Assay results from
this zone are awaited. Section 0 -- BGRB5D048, BGRB5D052, B5MB4D066
and B5MB4D067 clearly defined the limits to the deposit on this
section shown in Figure 5. GRB5D048 collared 10 metres east of the
Main Fault intersected three separate intervals of copper bearing
sub seafloor QVS mineralisation including: 7.80 metres grading
1.24% Cu, 0.08 g/t Au, 0.18% Zn and 2.1 g/t Ag from 57.20 metres,
10.00 metres grading 1.54% Cu, 0.07 g/t Au, 0.18% Zn and 1.4 g/t Ag
from 93.00 metres, and 15.11 metres grading 0.49% Cu, 0.02 g/t Au,
0.04% Zn and 1.1 g/t Ag from 113.89 metres. GRB5D052 drilled from
the western footwall intersected a 16.35 metre near true thickness
zone of QVS mineralisation from 90.54 metres which grades 0.72% Cu,
0.05 g/t Au, 0.13% Zn and 1.4 g/t Ag and includes 3.34 metres of
1.18% Cu, 0.04 g/t Au, 0.07% Zn and 1.3 g/t Ag. B5MB4D066 was sited
5 metres west of hole GRB5D048 to test for MS below surficial
gossan and it intersected the mineralised sequence from Fe and Cu
oxidised hanging wall basalts to 12.5 metres then gossan to 20
metres depth above supergene enriched MS and SMS with high grade
chalcocite + covellite down to 24 metres where the mineralised
interval was faulted out by a core parallel structure. Assay
results gave 22.7 metres of GOS/MS/SMS grading 3.76% Cu, 0.54 g/t
Au, 0.09% Zn and 15.4 g/t Ag from 1.5 metres depth including 4.9
metres grading 15.94% Cu, 1.27 g/t Au, 0.11% Zn and 49.4 g/t Ag
from 19.3 metres down hole in the supergene zone. B5MB4D067 was
sited 10 metres to the east of B5MB4D066 in order to provide a
better idea of the width of the MS mineralised zone and positions
of the faulted contacts. The hole successfully intersected a fault
on the east side of the mineralised zone at 28 metres and primary
MS with minor supergene enrichment to 38.65 metres then haematitic
sediment to 39.25 metres above a fault into footwall basalts at
39.7 metres. Assay results across this zone include 8.05 metres of
MS grading 3.18% Cu, 0.53 g/t Au, 0.39% Zn and 24 g/t Ag from 32.95
metres. It appears that the mineralised zones on this section are
of reasonable grade but are thinner than expected due to
considerable faulting and dyke intrusions. Section 1 -- B5MB4D064
and B5MB4D072 tested near surface extensions of the MS as shown in
Figure 4. B5MB4D064 was designed to test for MS below surficial
gossan exposed in a trench between drillholes D005 and D006.
B5MB4D064 successfully intersected clay-rich to haematitic gossan
and jasper from 12.5 metres -20.15 metres above supergene MS to
27.5 metres then primary chalcopyrite-rich MS to 36.8 metres
grading to SMS down to 51 metres above footwall QVS to 60 metres
where the Main Fault terminated mineralisation. This impressive
intersection totalling 39.5 metres of GOS/MS/SMS in B5MB4D064
grades 4.81% Cu, 0.25 g/t Au, 0.38% Zn and 16.7 g/t Ag from 13.5
metres down hole, including 16.85 metres grading 8.4% Cu, 0.25 g/t
Au, 0.52% Zn and 15.3 g/t Ag from 20.15 metres depth. B5MB4D072 was
a scissor hole designed to better constrain the shape and grade of
QVS below the strong MS in B5MB4D064 and above the well mineralised
GRB5D005 intersection. Unfortunately the hole intersected a series
of unmineralised structures and late dykes between ~97 metres and
~105 metres and then QVS between down to 107.34 metres where it
terminated on a cross fault. Assays are awaited but this result
minimises the effective width of the deposit on this section as
shown in Figure 4. Section 2 -- B5MB4D075 and B5MB4D079 tested
intermediate depth extensions of the MS and QVS. B5MB4D075 was
stopped at 122.10 metres having intersected 5.7 metres of MS at
91.63 metres close to where the hole crosses drillhole D020. It
also intersected several fault zones and breccias some of which
contain minor QVS mineralization and assays are awaited for this
hole. B5MB4D079 was stepped back to the west to intersect the QVS
zone at about 100 metres depth well below that of hole B5MB4D075.
B5MB4D079 intersected over 30 metres of moderate QVS mineralisation
from 95.25 to the end of the hole at 125.30 metres where the QVS
grades into brecciated basalts with only minor pyrite stringers.
Assays are awaited for this hole. Section 3 -- B5MB4D082 and
B5MB4D086 targeted the QVS zone at 50-100 metres depth. B5MB4D082
was set up at the same collar site as GRB5D032 but drilled a
steeper hole with the aim of intersecting QVS mineralisation
beneath the MS encountered in hole D030. B5MB4D082 successfully
intersected the Main Fault at 81.5 metres then the lowermost part
of the MS to 83.6 metres followed by QVS mineralisation with
chalcopyrite down to 119 metres. B5MB4D086 in progress is a step
back hole designed to test the position of the Main Fault, then the
grade and width of the QVS at 120 metres depth. Section 3.5 --
B5MB4D083 was an infill drill hole designed to test the continuity
between the 30 metre thick MS intersection of GRB5D030 and the 50
metre thick MS of GRB5D035. B5MB4D083 has confirmed the presence of
high-grade MS from 45.2-65.75 metres, SMS down to 72.4 metres and
16 metres QVS down to 88.5 metres. This good quality mineralised
zone awaiting sampling is slightly thinner than in D030 but appears
to be of equivalent grade on comparative logging. Summary Recent
drilling has clearly enhanced the deposit in terms of its size and
grade. Although original attributes of the VMS ore body can be
determined, the resultant form is clearly highly truncated by later
faulting - particularly at the deposit's southern end. In
these circumstances true widths of the ore intersections can be
difficult to determine. The deposit appears broadly constrained to
a northerly trending linear, penecontemporaneous fault and is at
least 300 metres long between Sections 1S to 5N. It comes to
surface on Section 2.5 with a well-developed gold gossan and
supergene enriched massive sulphides and plunges shallowly to the
north as shown in the long section Figure 2. In this figure, the
intersections shown are considered to represent 80-90% of the true
thickness of the deposit. Infill drilling on five intermediate 25
metre sections was required to determine ore shapes for ore body
modelling and provide additional core for metallurgical testing of
ore types. The deposit is potentially open down-plunge at depth to
the north where proposed drilling is underway. To the south,
the body appears to be terminated on a cross fault but extensions
may be possible and will be evaluated by using geophysics.
Qualified Person The exploration results disclosed in this press
release have been reviewed, verified (including sampling,
analytical and test data) and compiled by Dr. Peter Ruxton, who is
a Member of the Institute of Materials, Minerals and Mining
(I.M.M.M.), the Company's President and Chief Executive Officer and
a "qualified person" (as such term is defined in Canadian National
Instrument 43-101 as promulgated by the Canadian Securities
Administrators). Technical Report Additional information with
respect to the Company's Omani properties is contained in the
technical report prepared by Venmyn Rand (Pty) Ltd, dated December
31, 2010 and entitled "National Instrument 43-101 Independent
Technical Report on Block 5 and Block 6 Copper Projects, Semail
Ophiolite Belt, Sultanate of Oman held by Gentor Resources,
Inc." A copy of this report can be obtained from SEDAR at
www.sedar.com. About Gentor Gentor is a mineral exploration company
whose projects include copper and gold properties in the Sultanate
of Oman and a molybdenum-tungsten-silver property in East Central
Idaho, U.S. The Company's strategy is to create shareholder
value by developing highly prospective mineral properties around
the globe, with current focus in the Sultanate of Oman. In
Oman, Gentor is partnered with Al Fairuz Mining Company LLC on its
Block 5 exploration tenement and Al Zuhra Mining Company LLC on
Block 6. Cautionary Notes Forward-Looking Information: This press
release contains forward-looking information. All statements, other
than statements of historical fact, that address activities, events
or developments that the Company believes, expects or anticipates
will or may occur in the future (including, without limitation,
statements regarding drilling and other exploration results,
potential mineral resources, potential mineralization and the
Company's exploration and development plans) are forward-looking
information. This forward-looking information reflects the current
expectations or beliefs of the Company based on information
currently available to the Company. Forward-looking information is
subject to a number of risks and uncertainties that may cause the
actual results of the Company to differ materially from those
discussed in the forward-looking information, and even if such
actual results are realized or substantially realized, there can be
no assurance that they will have the expected consequences to, or
effects on the Company. Factors that could cause actual results or
events to differ materially from current expectations include,
among other things, risks related to the exploration stage of the
Company's properties, the possibility that future exploration
results will not be consistent with the Company's expectations,
changes in world copper or gold markets and equity markets,
political developments in Oman, uncertainties relating to the
availability and costs of financing needed in the future, the
uncertainties involved in interpreting exploration results and
other geological data and the other risks involved in the mineral
exploration business. Forward-looking information speaks only as of
the date on which it is provided and, except as may be required by
applicable securities laws, the Company disclaims any intent or
obligation to update any forward-looking information, whether as a
result of new information, future events or results or otherwise.
Although the Company believes that the assumptions inherent in the
forward-looking information are reasonable, forward-looking
information is not a guarantee of future performance and
accordingly undue reliance should not be put on such information
due to the inherent uncertainty therein. The United States
Securities and Exchange Commission (the "SEC") permits mining
companies, in their filings with the SEC, to disclose only those
mineral deposits that a company can economically and legally
extract or produce. U.S. investors are cautioned not to assume that
any disclosure of mineralization contained in this press release is
economically or legally mineable. U.S. investors are urged to
closely consider all of the disclosures in the Company's reports
filed pursuant to the United States Securities Exchange Act of 1934
which may be secured from the Company, or from the SEC's website at
http://www.sec.gov/edgar.html. Neither TSX Venture Exchange nor its
Regulation Services Provider (as that term is defined in the
policies of the TSX Venture Exchange) accepts responsibility for
the adequacy or accuracy of this release. SOURCE
Gentor Resources Inc. Image with caption: "FIGURE 1- Mahab 4
geological plan showing drill holes, geology and mineralised
intervals. (CNW Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6559.jpg
Image with caption: "FIGURE 2- Mahab 4 geological long section
showing drill holes, geological interpretation and mineralised
intervals. (CNW Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6560.jpg
Image with caption: "FIGURE 3- Mahab 4, Section 4 with drill holes,
geological interpretation and mineralised intervals. (CNW
Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6561.jpg
Image with caption: "FIGURE 4- Mahab 4 Section 1 with drill holes,
geological interpretation and mineralised intervals. (CNW
Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6562.jpg
Image with caption: "FIGURE 5- Mahab 4, Section 0 with drill holes,
geological interpretation and mineralised intervals. (CNW
Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6563.jpg
Image with caption: "FIGURE 6- Mahab 4, Section 1S with drill
holes, geological interpretation and mineralised intervals. (CNW
Group/Gentor Resources Inc.)". Image available at:
http://photos.newswire.ca/images/download/20111114_C5175_PHOTO_EN_6564.jpg
Gentor Resources Inc. CONTACT: please visit our website at
www.gentorresources.com, or contact:Dr.Peter Ruxton, President
& CEO, United Kingdom Tel: + 44 (0) 7786111103; or Arnold T.
Kondrat, Executive Vice President, Toronto,Ontario, Tel: + 1 (416)
366 2221 or + 1 (800) 714 7938.
Copyright
Gentor Resources (TSXV:GNT)
Gráfica de Acción Histórica
De May 2024 a Jun 2024
Gentor Resources (TSXV:GNT)
Gráfica de Acción Histórica
De Jun 2023 a Jun 2024